长江河口潮波传播机制及阈值效应分析   总被引：1，自引：0，他引：1  

张先毅  黄竞争  杨昊  欧素英  刘锋  蔡华阳  杨清书 《海洋与湖沼》2019,50(4):788-798

河口潮波传播过程受沿程地形(如河宽辐聚、水深变化)及上游径流等诸多因素影响,时空变化复杂。径潮动力非线性相互作用研究有利于揭示河口潮波传播的动力学机制,对河口区水资源高效开发利用具有重要指导意义。本文基于2007—2009年长江河口沿程天生港、江阴、镇江、南京、马鞍山、芜湖的逐日高、低潮位数据及大通站日均流量数据,统计分析不同河段潮波衰减率与余水位坡度随流量的变化特征,结果表明潮波衰减率绝对值与余水位坡度随流量增大并不是单调递增,而是存在一个阈值流量和区域,对应潮波衰减效应的极大值。为揭示这一阈值现象,采用一维水动力解析模型对研究河段的潮波传播过程进行模拟。结果表明,潮波传播的阈值现象主要是由于洪季上游回水作用随流量加强,余水位及水深增大,导致河口辐聚程度减小,而余水位坡度为适应河口形状变化亦有所减小,从而形成相对应的阈值流量和区域。  相似文献   

三峡库区龙门寨危岩体崩塌产生涌浪研究   总被引：1，自引：1，他引：0  

郑嘉豪  黄波林  张全  赵海林  冯万里  王健  陈小婷 《地质力学学报》2020,26(4):533-543

长江两岸高耸的危岩体对航道、沿岸居民带来巨大安全隐患。大宁河属于长江一级支流，龙门寨危岩体位于大宁河上，距离巫山县城仅1 km。利用FLOW-3D软件，模拟了145 m、175 m两种水位工况下龙门寨危岩体崩塌产生涌浪过程和涌浪传播过程。模拟结果表明，涌浪在145 m水位工况下最大浪高约为17.9 m，175 m水位工况下最大浪高约为11.6 m；在巫山县的五个码头处，两种水位工况最大涌浪爬高分别约为10.9 m、3.8 m；根据涌浪高度，对大宁河进行危险分区，145 m水位工况下极高危险区长度约4.4 km，很高危险区长度约1.9 km；175 m水位工况下极高危险区长度约3.0 km，很高危险区长度约1.0 km。研究结果有助于防控龙门寨危岩体潜在涌浪灾害危害，保障大宁河航道和巫山县码头安全，同时也为三峡库区滑坡涌浪灾害提供了预警依据。   相似文献   

Deposition and preservation of fluvio-tidal shallow-marine sandstones: A re-evaluation of the Neoproterozoic Jura Quartzite (western Scotland)     

Bruce K. Levell  Howard D. Johnson  Daniel S. Collins  Marijn van Cappelle 《Sedimentology》2020,67(1):173-206

The 2 to 5 km thick, sandstone-dominated (>90%) Jura Quartzite is an extreme example of a mature Neoproterozoic sandstone, previously interpreted as a tide-influenced shelf deposit and herein re-interpreted within a fluvio-tidal deltaic depositional model. Three issues are addressed: (i) evidence for the re-interpretation from tidal shelf to tidal delta; (ii) reasons for vertical facies uniformity; and (iii) sand supply mechanisms to form thick tidal-shelf sandstones. The predominant facies (compound cross-bedded, coarse-grained sandstones) represents the lower parts of metres to tens of metres high, transverse fluvio-tidal bedforms with superimposed smaller bedforms. Ubiquitous erosional surfaces, some with granule–pebble lags, record erosion of the upper parts of those bedforms. There was selective preservation of the higher energy, topographically-lower, parts of channel-bar systems. Strongly asymmetrical, bimodal, palaeocurrents are interpreted as due to associated selective preservation of fluvially-enhanced ebb tidal currents. Finer-grained facies are scarce, due largely to suspended sediment bypass. They record deposition in lower-energy environments, including channel mouth bars, between and down depositional-dip of higher energy fluvio-ebb tidal bars. The lack of wave-formed sedimentary structures and low continuity of mudstone and sandstone interbeds, support deposition in a non-shelf setting. Hence, a sand-rich, fluvial–tidal, current-dominated, largely sub-tidal, delta setting is proposed. This new interpretation avoids the problem of transporting large amounts of coarse sand to a shelf. Facies uniformity and vertical stacking are likely due to sediment oversupply and bypass rather than balanced sediment supply and subsidence rates. However, facies evidence of relative sea level changes is difficult to recognise, which is attributed to: (i) the areally extensive and polygenetic nature of the preserved facies, and (ii) a large stored sediment buffer that dampened response to relative sea-level and/or sediment supply changes. Consideration of preservation bias towards high-energy deposits may be more generally relevant, especially to thick Neoproterozoic and Lower Palaeozoic marine sandstones.  相似文献   

江苏海岸中部近岸冬季潮汐和潮流特征     

王逸涵  王韫玮  于谦  蔡辉  高抒 《海洋科学》2019,43(10):66-74

南黄海西侧的江苏海岸近岸区域,素以地形复杂、潮流强劲、悬沙输运剧烈著称,但是较长期的同步潮位和潮流观测数据仍然缺乏,尤其是在近岸(20 km)浅水(20 m)区域。2014年1月在大丰港附近开展了连续潮位和潮流观测,获得的数据揭示了一系列特征。此地潮汐潮流为正规半日潮,浅水分潮显著。平均潮差为3.05 m,最显著的两个分潮为M2和S2分潮,振幅分别为1.45 m和0.52 m。潮流最显著的半日分潮M2分潮和最显著的浅水分潮M4分潮在沿岸方向上振幅分别为0.84m/s和0.12m/s,在跨岸方向上振幅分别为0.24 m/s和0.01 m/s,沿岸方向占绝对优势。潮波的沿岸传播介于前进波和驻波之间,驻波的特征稍强。M2分潮潮流椭圆最大流(长轴)方向为南偏东7.4°。存在冬季沿岸向北的余流,垂向平均值的大小为2.2 cm/s。以上潮汐潮流特征为该区域海洋物质输运研究提供了基础资料。  相似文献   

Three-dimensional finite element simulation of fracture propagation in rock specimens with pre-existing fissure(s) under compression and their strength analysis     

Ramin Pakzad  Shanyong Wang  Scott W. Sloan 《国际地质力学数值与分析法杂志》2020,44(10):1472-1494

A FORTRAN program, consistent with the commercially available finite element (FE) code ABAQUS, is developed based on a three-dimensional (3D) linear elastic brittle damage constitutive model with two damage criteria. To consider the heterogeneity of rock, the developed FORTRAN program is used to set the stiffness and strength properties of each element of the FE model following a Weibull distribution function. The reliability of the program is assessed against available experimental results for granite cylindrical specimens with a throughgoing, flat and inclined fissure. The calibration procedure of the material parameters is explained in detail, and it is shown that the compressive to tensile strength ratio can have a substantial influence on the failure response of the specimens. Numerical simulations are conducted for models with different levels of heterogeneity. The results show a smaller load bearing capacity for models with less homogeneity, representing gradual coalescence of fully damaged elements forming throughout the models during loading. The maximum load bearing capacity is studied for various combinations of inclination angles of two centrally aligned, throughgoing and flat fissures of equal length embedded in cylindrical models under uniaxial and multiaxial loading conditions. The key role of the compressive to tensile strength ratio is highlighted by repeating certain simulations with a lower compressive to tensile strength ratio. It is proven that the peak loads of the rock models with sufficiently small compressive to tensile strength ratios containing two throughgoing fissures of equal length are similar, provided that the minimum inclination angles of the models are the same. The results are presented and discussed with respect to the existing experimental findings in the literature, suggesting that the numerical model applied in this study can provide useful insight into the failure behaviour of rock-like materials.  相似文献   

潮流界以下河段航道整治水位确定方法研究——以长江江阴以下河段为例     

徐元  贾雨少 《海洋工程》2018,36(2):64-72

在总结分析现有整治水位确定方法的基础上,根据潮流界以下河段的水沙运动特性,本文提出一种基于输沙能力的航道整治水位确定方法。考虑上游来水、下游潮汐为独立事件,统计潮流界以下河段上游来水、下游潮汐不同等级组合出现的频率,采用数学模型计算相应组合下河段沿程的潮位、流速过程,以流速四次方代表水流的输沙能力,统计不同潮位等级对应的综合净输沙能力,确定最大综合净输沙能力对应的水位为(最优)航道整治水位。以长江下游白茆沙水道和福姜沙水道为例,计算了所在河段的航道整治水位,并探讨了起动流速对整治水位计算的影响和最高整治水位概念对工程的意义。  相似文献   

Analytical study of ground motion caused by seismic wave propagation across faulted rock masses          下载免费PDF全文

J.C. Li  N.N. Li  S.B. Chai  H.B. Li 《国际地质力学数值与分析法杂志》2018,42(1):95-109

Studying seismic wave propagation across rock masses and the induced ground motion is an important topic, which receives considerable attention in design and construction of underground cavern/tunnel constructions and mining activities. The current study investigates wave propagation across a rock mass with one fault and the induced ground motion using a recursive approach. The rocks beside the fault are assumed as viscoelastic media with seismic quality factors, Q_p and Q_s. Two kinds of interactions between stress waves and a discontinuity and between stress waves and a free surface are analyzed, respectively. As the result of the wave superposition, the mathematical expressions for induced ground vibration are deduced. The proposed approach is then compared with the existing analysis for special cases. Finally, parametric studies are carried out, which includes the influences of fault stiffness, incident angle, and frequency of incident waves on the peak particle velocities of the ground motions.  相似文献   

Implementation of a coupled plastic damage distinct lattice spring model for dynamic crack propagation in geomaterials          下载免费PDF全文

Chao Jiang  Gao‐Feng Zhao 《国际地质力学数值与分析法杂志》2018,42(4):674-693

This paper studies dynamic crack propagation by employing the distinct lattice spring model (DLSM) and 3‐dimensional (3D) printing technique. A damage‐plasticity model was developed and implemented in a 2D DLSM. Applicability of the damage‐plasticity DLSM was verified against analytical elastic solutions and experimental results for crack propagation. As a physical analogy, dynamic fracturing tests were conducted on 3D printed specimens using the split Hopkinson pressure bar. The dynamic stress intensity factors were recorded, and crack paths were captured by a high‐speed camera. A parametric study was conducted to find the influences of the parameters on cracking behaviors, including initial and peak fracture toughness, crack speed, and crack patterns. Finally, selection of parameters for the damage‐plasticity model was determined through the comparison of numerical predictions and the experimentally observed cracking features.  相似文献   

2016下半年安达曼海潮、余流观测分析     

刘延亮  郭景松  王辉武  薛宇欢  KHOKIATTIWONG Somkiat  于卫东 《海洋学报(英文版)》2018,37(9):13-21

The characteristics of currents and tidal currents in the Andaman Sea(AS) are studied during the second half of2016 using observed data from a moored acoustic Doppler current profiler(ADCP) deployed at 8.6°N, 95.6°E.During the observation period, the mean flow is 5–10 cm/s and largely southward. The root mean square and kinetic energies of the low and high frequency flows, which are divided by a cutoff period of 5 d, are at the same level, indicating their identical importance to the total current. A power spectrum analysis shows that intraseasonal oscillations, a tidal-related semilunar month signal, a semidiurnal tidal signal and periods of 3–4 d are prominent. The barocliny of an eddy kinetic energy is stronger than the mean kinetic energy, both of which are the strongest on the bottom and the weakest at 70 m depth. Residual currents are largely southward(northward) during the summer(winter) monsoon season. Two striking peaks of the southward flow cause the 80 d period of meridional currents. The first peak is part of a large-scale circulation, which enters the AS through the northern channel and exits through the southern channel, and the second peak is part of a local vortex. The 40 d oscillation of the zonal current is forced by geostrophic variations attributed to local and equatorial remote forcing. The tidal current is dominated by semidiurnal constituents, and among these, M2 and N2 are the top two largest major axes. Moreover, astronomical tidal constituents MM and MSF are also significant. Diurnal constituents are weak and shallow water tides are ignorable. The aims are to introduce the new current data observed in the AS and to provide initial insights for the tidal and residual currents in the Andaman Sea.  相似文献   

基于UDF的水平轴潮流能水轮机被动旋转水动力性能研究   总被引：1，自引：1，他引：0  

陈文鹏  刘胤超  陈立卫 《海洋工程》2018,36(2):119-126

针对水平轴潮流能水轮机被动旋转问题,基于Fluent 17.0,运用UDF(User Defined Function)控制滑移网格对网格进行动态调整,仿真研究水轮机在不同安放角下被动旋转的水动力特性。通过仿真分析,结果表明:潮流能水轮机随着叶片安放角度的增加,尖速比、输出功率、捕能系数都是先增大后减小,叶片安放角为6°时,叶轮前后速度差最大,对潮流能利用充分,且各项性能均达到最佳;通过分析叶片受力,叶尖叶素在安放角为2°时阻力最大,3°时升力最大,升阻比在6°时最大,此时叶尖叶素升阻比C_L/C_D=6.27、攻角α=3.06°。由仿真结果可知水平轴潮流能叶轮的自启动过程由5个阶段组成,即加速度增大的加速运动段—加速度减小的加速运动段—加速度反向增大的减速运动段—加速度反向减小的减速运动段—稳定运行段,这对潮流能水轮机的设计具有重要的指导意义。  相似文献